RF Combiner Splitter Couplers & Hybrids Includes:
Combiner, splitter, coupler hybrids overview Splitters & Combiners Resistive splitter & combiner Hybrid splitter & combiner Wilkinson splitter & combiner Directional coupler
RF power splitters / dividers or combiners can very easily be designed and constructed using just resistors.
Resistive power dividers / splitters / combiners are cheap and easy to manufacture and they are often used in low cost television antenna splitters . Nevertheless they have some advantages that mean they can provide effective performance over a wide range of frequencies, maintaining an accurate impedance match.
Resistive splitter combiner advantages and disadvantages
As may be imagined, resistive splitters and resistive combiners have a number of advantages and disadvantages. These need to be considered when deciding what form of splitter / combiner to use or design into some equipment.
Resistive splitter advantages
- Simplicity: A resistive splitter / combiner is particularly simple, being made up from only resistors. They can be made very easily within a circuit requiring little design and preparation.
- Cost: Being made from only resistors, the cost of a resistive combiner / splitter is very low.
- Frequency response: Provided that suitable resistors and construction techniques are used, the frequency response can extend over a wide frequency range.
Resistive splitter disadvantages
- Loss: Using resistors, power is lost over an above the reduction in power level resulting from the division of the power between several outputs in a splitter. For a two way resistive splitter an additional 3dB power loss is incurred over the split reduction of 3dB (resulting from splitting the power two ways).
- Isolation: There is little isolation between the output ports.
Resistive splitter divider basics
There is a variety of different types of resistive RF divider or splitter. They can be used to provide an RF split or division in any ratio, simply by choosing the correct values of resistor and configuration.
Resistive splitters are also able to provide an accurate impedance match over a wide band of frequencies provided the correct types of resistor and construction techniques are used. Consisting of just resistors, they are able to easily provide a very good impedance match.
A variety of different configurations can be used for RF resistive power splitters / RF resistive power dividers.
6 dB three way resistive power divider / splitter
One of the most commonly seen forms of resistive power divider or power splitter is the simple three way resistive splitter or divider. There are two configurations that can be seen - namely star or delta configurations.
- Star format power splitter divider: The star format for the power divider splitter is possibly the more widely used of the two formats.
In the star example, the series resistors to the star point are all equal and have a resistance that has a value:
- Delta splitter divider combiner: The delt format for use as a power divider / splitter is seen on many occasions.
In this example the resistance of the resistors is equal to that of the characteristic impedance of the RF system.
With these simple forms of resistive power divider or splitter, any port can be used as the input, the remaining ones being used as the outputs. The outputs are 6 dB down on the input level, 3 dB of additional losses are incurred over the level reduction of 3 dB that would be experienced if an ideal transformer based "hybrid" splitter was used that incurred no dissipative losses.
A further point to note about this form of resistive power divider / splitter is that there is 6 dB of isolation between the ports. This may be anticipated from the fact that the loss of the input signal is also 6 dB.
N-1 way resistive power divider, splitter, combiner
It is possible to make resistive power dividers that have any number of ports. Power reductions will obviously be greater, but in many instances it will be possible to tolerate these increased losses. The most straightforward design is based upon the star power divider configuration. It is achieved by simply linking more resistors and ports to the star point.
For any number of outputs, there will be N ports - the additional port being required for the input.
Resistive power dividers or power splitters / combiners are easy to implement and use provided that the resistive losses can be accommodated. They offer a wideband performance and they are cheap and easy to implement and these factors make them very attractive for many applications.
More Essential Radio Topics:
Radio Signals Modulation types & techniques Amplitude modulation Frequency modulation OFDM RF mixing Phase locked loops Frequency synthesizers Passive intermodulation RF attenuators RF filters Radio receiver types Superhet radio Radio receiver selectivity Radio receiver sensitivity Receiver strong signal handling
Return to Radio topics menu . . .